manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

’03 MATRIX_U (L/O 0201)

98

2003 MY COROLLA MATRIX_U (OM12767U)

(g) Parking

1. Bring the vehicle to a complete stop.

2. With the brake pedal pressed down,

fully depress the parking brake pedal
to apply the parking brake securely.

3. With the brake pedal pressed down,

shift the selector lever to the “P” posi-
tion.

CAUTION

Never attempt to move the selector
lever into “P” position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.

(h) Good driving practice

If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.

CAUTION

Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.

NOTICE

Always use the brake pedal or the
parking brake to hold the vehicle on
an upgrade. Do not attempt to hold
the vehicle using the accelerator ped-
al, as this can cause the transmission
to overheat.

(i)

Rocking your vehicle if stuck

CAUTION

If your vehicle becomes stuck in
snow, mud, sand, etc., then you may
attempt to rock the vehicle free by
moving it forward and backward. Do
not attempt this procedure if people
or objects are anywhere near the ve-
hicle. During the rocking operation
the vehicle may suddenly move for-
ward or backward as it becomes un-
stuck, causing injury or damage to
nearby people or objects.

NOTICE

If you rock your vehicle, observe the
following precautions to prevent dam-
age to the transmission and other
parts.

Do not depress the accelerator ped-
al while shifting the selector lever
or before the transmission is com-
pletely shifted to forward or reverse
gear.

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 94
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Brand: FANATEC Pages: 9
Warrior Products 3860 Quick Start Manual preview
3860
Brand: Warrior Products Pages: 2
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 20
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Brand: Neuspeed Pages: 2
Saab 32 025 888 Installation Instructions preview
32 025 888
Brand: Saab Pages: 3
iArmor EDGE IA-N098 Quick Start Manual preview
EDGE IA-N098
Brand: iArmor Pages: 4
Whispbar K678W Fitting Instructions Manual preview
K678W
Brand: Whispbar Pages: 14
Whispbar K919W Fitting Instructions Manual preview
K919W
Brand: Whispbar Pages: 17
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Brand: Fisher Body Pages: 37
Manik 519952T Installation Instructions preview
519952T
Brand: Manik Pages: 2
Toyota SUPRA 1987 Electrical Wiring Diagram preview
SUPRA 1987
Brand: Toyota Pages: 165
Joie i-Level Instruction Manual preview
i-Level
Brand: Joie Pages: 53
Yakima K896 Instructions Manual preview
K896
Brand: Yakima Pages: 12
Navman T1 F20 User Manual preview
T1 F20
Brand: Navman Pages: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Brand: Macrom Pages: 10

Brands by name

Popular brands

Load more brands