manualshive.com logo in svg

Toyota Matrix 2003, Operating Manual

The Toyota Matrix 2003 Owner's Manual is a comprehensive guide that provides essential information for owners. Easily download this manual for free from manualshive.com to gain valuable insights on maintenance, troubleshooting, and operating instructions. Experience the convenience of accessing this indispensable resource for your Toyota Matrix 2003.

Share
Download
background image

’03 MATRIX_U (L/O 0201)

36

2003 MY COROLLA MATRIX_U (OM12767U)

Take up
slack

Too high

Keeps as low on
hips as possible

Adjust the position of the lap and
shoulder belts.

Position the lap belt as low as possible
on your hips—not on your waist, then ad-
just it to a snug fit by pulling the shoulder
portion upward through the latch plate.

CAUTION

Both high–positioned lap belts and
loose–fitting belts could cause seri-
ous injuries due to sliding under
the lap belt during a collision or
other unintended result. Keep the
lap belt positioned as low on hips
as possible.

For your safety, do not place the
shoulder belt under your arm.

To release the belt, press the buckle–re-
lease button and allow the belt to re-
tract.

If the belt does not retract smoothly, pull
it out and check for kinks or twists. Then
make sure it remains untwisted as it re-
tracts.

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

cam HS Series Operating Manual preview
HS Series
Brand: cam Pages: 28
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Brand: Jeep Pages: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Brand: Jeep Pages: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Brand: Jeep Pages: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Brand: Jeep Pages: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Brand: Jeep Pages: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Brand: Jeep Pages: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Brand: Jeep Pages: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Brand: Jeep Pages: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Brand: Jeep Pages: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Brand: Jeep Pages: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Brand: Jeep Pages: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Brand: Jeep Pages: 50
Jeep Grand Cherokee SRT 2014 Owner'S Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 118
Jeep 2014 Grand Cherokee Accessories Quick Reference Manual preview
2014 Grand Cherokee
Brand: Jeep Pages: 24

Brands by name

Popular brands

Load more brands