Toyota Matrix 2003 Operating Manual Download Page 22 | Manualshive

Page: 22 / 306

background image

’03 MATRIX_U (L/O 0201)

22

2003 MY COROLLA MATRIX_U (OM12767U)

3. Hold the hood open by inserting the

support rod into the slot.

To insert the support rod into the slot,
move it straight up. If it is moved to the
side or toward the inside of the vehicle,
it may become detached.

Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. and return the support rod to its
clip—this prevents rattles. Then lower the
hood and make sure it locks into place.
If necessary, press down gently on the
front edge to lock it.

CAUTION

After inserting the support rod into
the slot, make sure the rod supports
the hood securely from falling down
on to your head or body.

NOTICE

Be sure to return the support rod to
its clip before closing the hood. Clos-
ing the hood with the support rod up
could cause the hood to bend.

This indicates that the fuel filler door
is on the left side of your vehicle.

Fuel tank cap

«
...
20
21
22
23
24
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: 3SIXT Pages: 12

Brand: Tessera4x4 Pages: 20

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: Mazda Pages: 13

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: BrandMotion Pages: 2

Impala Limited 2014

Brand: Chevrolet Pages: 356

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: VER-MAC Pages: 64

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands