Toyota Matrix 2003 Operating Manual Download Page 205 | Manualshive

Page: 205 / 306

background image

’03 MATRIX_U (L/O 0201)

205

2003 MY COROLLA MATRIX_U (OM12767U)

To remove the jack, unhook the tightening
strap.

To store the jack, make sure it is securely
held by the tightening strap.

To remove the spare tire:

1. Loosen the nut and remove it.

2. Remove the luggage storage box.

3. Loosen the bolt and remove it.

When storing the spare tire, put it in place
with the inner side of the wheel facing up.
Then secure the tire by repeating the
above removal steps in reverse order to
prevent it from flying forward during a
collision or sudden braking.

The compact tire storage area is designed
only for a compact spare tire. Standard
size tires cannot be stored in this storage
area.

2. Block the wheel diagonally opposite

the flat tire to keep the vehicle from
rolling when it is jacked up.

When blocking the wheel, place a wheel
block from the front for the front wheels
or from the rear for the rear wheels.

—Blocking the wheel

«
...
203
204
205
206
207
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: M7 SPEED Pages: 11

Brand: TATA Motors Pages: 156

Brand: Kia Pages: 10

Brand: Dodge Pages: 24

Brand: Fab Fours Pages: 19

Brand: Webasto Pages: 18

Brand: Kuda Pages: 2

Brand: Buick Pages: 20

Brand: Anker Technology Pages: 8

Brand: Curtis Pages: 6

PRIME DESIGN VRR3-FT21G-ST

Brand: Safe Fleet Pages: 12

2013 2500 Big Horn

Brand: RAM Pages: 12

Brand: Mobridge Pages: 20

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands