Toyota Matrix 2003 Operating Manual Download Page 232 | Manualshive

Page: 232 / 306

background image

’03 MATRIX_U (L/O 0201)

240

2003 MY COROLLA MATRIX_U (OM12767U)

Do not start or run the engine while
your vehicle is supported by the
jack.

Stop the vehicle on a level firm
ground, firmly set the parking brake
and put the transmission in “P”
(automatic) or reverse (manual).
Block the wheels on the opposite
side of the jack up point if neces-
sary.

Make sure to set the jack properly
in the jack point. Raising the ve-
hicle with jack improperly posi-
tioned will damage the vehicle or
may allow the vehicle to fall off the
jack and cause personal injury.

Never get under the vehicle when
the vehicle is supported by the jack
alone; use vehicle support stands.

Do not raise the vehicle with some-
one in the vehicle.

When raising the vehicle, do not
place any objects on top of or un-
derneath the jack.

NOTICE

Make sure to place the jack correctly,
or your vehicle may be damaged.

«
...
230
231
232
233
234
...
»

Summary of Contents for Matrix 2003



















































































































































































































































































































Reviews:

No comments

Related manuals for Matrix 2003

Brand: EAL Pages: 4

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: Metra Electronics Pages: 2

Brand: Quadratec Pages: 12

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: E&G Classics Pages: 3

Brand: GMC Pages: 430

Brand: rockymounts Pages: 6

Brand: Calix group Pages: 4

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Xingyun Pages: 74

Brand: Yakima Pages: 11

2011 Camry SE V6

Brand: Toyota Pages: 33

Brand: SSV Works Pages: 2

Brand: Setma Pages: 13

Brand: Cadillac Pages: 508

Brand: Kia Pages: 289

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands