Toyota Matrix 2003 Operating Manual Download Page 263

Page: 263 / 306

’03 MATRIX_U (L/O 0201)

271

2003 MY COROLLA MATRIX_U (OM12767U)

TRANSFER
(four–wheel drive models)

Oil capacity, L (qt., Imp. qt.):

0.8 (0.8, 0.7)

Oil type:

Hypoid gear oil API GL–5

Recommended oil viscosity:

Above –18

C (0

SAE 90

Below –18

C (0

SAE 80W or 80W–90

REAR DIFFERENTIAL
(four–wheel drive models)

Oil capacity, L (qt., Imp. qt.):

0.5 (0.5, 0.4)

Oil type:

Hypoid gear oil API GL–5

Recommended oil viscosity:

Above –18

C (0

SAE 90

Below –18

C (0

SAE 80W or 80W–90

BRAKES

Minimum pedal clearance when depressed
with the force of 490 N (50 kgf, 110 lbf)
with the engine running, mm (in.):

70 (2.8)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when pulled with
the force of 196 N (20 kgf, 44 lbf):

5—8 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING

Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRON

or III

Summary of Contents for Matrix 2003



















































































































































































































































































































Search results

Summary of Contents for Matrix 2003

Reviews:

Related manuals for Matrix 2003

Brands by name

Popular brands

Toyota Matrix 2003, Operating Manual

Search results

Summary of Contents for Matrix 2003

Reviews:

Related manuals for Matrix 2003

Brands by name

Popular brands