Toshiba GRT100 Series Instruction Manual Download Page 67 | Manualshive

Page: 67 / 270

background image



66



6

F

2

S

0

7

8

9

4. User Interface

4.1 Outline of User Interface

The user can access the relay from the front panel.

Local communication with the relay is also possible using a personal computer (PC), equipped
with the RSM (Relay Setting and Monitoring) software via an RS232C port. Furthermore,
remote communication is also possible using a PC equipped with the RSM via an RS485 and a
protocol converter.

This section describes the front panel configuration and the basic configuration of the menu tree
of the local human machine communication ports and HMI (Human Machine Interface).

4.1.1 Front Panel

As shown in Figure 3.1.13, the front panel is provided with a liquid crystal display (LCD), light
emitting diodes (LED), operation keys,

VIEW

and

RESET

keys, monitoring jack and

RS232C connector.

LCD

The LCD screen, provided with a 4-line, 40-character back-light, displays detailed information
of the relay interior such as records, status and setting. The LCD screen is normally unlit, but
pressing the

VIEW

key will display the digest screen and pressing any key other than

VIEW

and

RESET

will display the menu screen.

These screens are turned off by pressing the

RESET

key or

END

key. If any display is left for

5 minutes or longer without operation, the back-light will go off.

LED

There are 8 LED displays. The signal labels and LED colours are defined as follows:

Label

Color

Remarks

IN SERVICE

Green

Lit when the relay is in service.

TRIP

Red

Lit when a trip command is issued.

ALARM

Red

Lit when a failure is detected.

TESTING

Red

Lit when disabling automatic monitoring function or resetting the
time counting of THR and V/F elements by the scheme switches.

(LED1)

Red

(LED2)

Red

(LED3)

Red

(LED4)

Red

LED1 to LED4 are configurable.

The TRIP LED lights up once the relay is operating and remains lit even after the trip command
goes off. The TRIP LED can be turned off by pressing the

RESET

key. Other LEDs are lit as

long as a signal is present and the

RESET

key is invalid while the signal is being maintained.

«
...
65
66
67
68
69
...
»

Summary of Contents for GRT100 Series















































































































































































































































































Reviews:

No comments

Related manuals for GRT100 Series

Brand: Gerni Pages: 60

Brand: MAHLE Pages: 36

Brand: S&B Filters Pages: 16

Brand: Nedap Pages: 24

Brand: IAG Pages: 7

Brand: Omron Pages: 2

Brand: Omron Pages: 2

Brand: Omron Pages: 2

Brand: Omron Pages: 10

Brand: Omron Pages: 168

Brand: TDR Pages: 3

Biopel Ash Removal 10/15

Brand: Opop Pages: 62

Brand: Grout Groovy Pages: 8

Brand: Tiger Pages: 20

Brand: WeLens Pages: 7

Brand: Starmobile Pages: 20

Brand: Steelcraft Pages: 5

Brand: Strongarm Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands