TLV EF200F-C Instruction Manual Download Page 117

Page: 117 / 181

EF200F-C

Operation

117

Parameter

Prerequisite

Description

User interface

Energy ﬂow

With order code for "Sensor version":
• option "Mass (integrated

temperature measurement)"
or

• option "Mass (integrated pressure/

temperature measurement)"

Displays the energy ﬂow that is
currently calculated.

Dependency
The unit is taken from the Energy ﬂow
unit parameter (→ See 10.4.2).

Signed ﬂoating-point
number

Heat ﬂow diﬀerence

• In the Select gas type parameter

(→ See 10.4.3), one of the following
options is selected:
Single gas
Gas mixture
Natural gas
User-speciﬁc gas

Displays the heat ﬂow diﬀerence that is
currently calculated.

Dependency
The unit is taken from the Energy ﬂow
unit parameter (→ See 10.4.2).

Signed ﬂoating-point
number

Reynolds number

Displays the Reynolds number that is
currently calculated.

Signed ﬂoating-point
number

Density

Displays the density currently
measured.

Dependency
The unit is taken from the Density unit
parameter.

Positive ﬂoating-point
number

Speciﬁc volume

Displays the current value for the
speciﬁc volume.

Dependency
The unit is taken from the Speciﬁc
volume unit parameter.

Positive ﬂoating-point
number

Pressure

The Pressure option is selected in the

External value parameter.

Displays the current process pressure.

Dependency
The unit is taken from the Pressure
unit parameter.

0 to 250 bar

Compressibility factor

The Gas option or the Steam option is
selected in the Select medium
parameter.

Displays the compressibility factor
currently calculated.

0 to 2

Degrees of superheat

In the Select medium parameter, the
Steam option is selected.

Displays the degree of superheating
currently calculated.

0 to 500 K

Summary of Contents for EF200F-C





















































































































































































Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands

TLV EF200F-C, Instruction Manual

Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands