TLV EF200F-C Instruction Manual Download Page 128 | Manualshive

Page: 128 / 181

background image

Diagnostics and troubleshooting

EF200F-C

128

12.3.2 Adapting the status signal

Each item of diagnostic information is assigned a speciﬁc status signal at the factory. The
user can change this assignment for speciﬁc diagnostic information in the Diagnostic
event category submenu.

Expert → Communication → Diagnostic event category

Available status signals

Conﬁguration as per HART 7 Speciﬁcation (Condensed Status), in accordance with
NAMUR NE107.

Symbol

Meaning

A0013956

Failure
A device error is present. The measured value is no longer valid.

A0013959

Function check
The device is in service mode (e.g. during a simulation).

A0013958

Out of speciﬁcation
The device is being operated:
• Outside its technical speciﬁcation limits (e.g. outside the process temperature range)
• Outside of the conﬁguration carried out by the user (e.g. maximum ﬂow in parameter

20 mA value )

A0013957

Maintenance required
Maintenance is required. The measured value is still valid.

A0023076

Has no eﬀect on the condensed status.

12.4 Overview of diagnostic information

The amount of diagnostic information and the number of measured variables aﬀected
increase if the measuring device has one or more application packages.

In the case of some items of diagnostic information, the status signal and the
diagnostic behavior can be changed. Change the diagnostic information → See 12.3.1

Diagnostic

number

Short text

Remedy instructions

Status

signal

[from the

factory]

Diagnostic

behavior

[from the

factory]

Diagnostic of sensor

004

Sensor defective

1. Check plug connections
2. Change pre-ampliﬁer
3. Change DSC sensor

F

Alarm

022

Temperature sensor
defective

1. Check plug connections
2. Change pre-ampliﬁer
3. Change DSC sensor

F

Alarm

1)

046

Sensor limit exceeded

1. Check plug connections
2. Change pre-ampliﬁer
3. Change DSC sensor

S

Warning

«
...
126
127
128
129
130
...
»

Summary of Contents for EF200F-C






















































































































































































Reviews:

No comments

Related manuals for EF200F-C

Brand: VeEX Pages: 2

Brand: Aaronia Pages: 47

Brand: Xylem Pages: 24

Brand: Abus Pages: 168

Brand: OHAUS Pages: 76

MTEK6000 Series

Brand: Metretek Pages: 81

HydroTracer FLV

Brand: aboni Pages: 48

Brand: OHAUS Pages: 84

XL4 SECOND STAGE

Brand: Apeks Pages: 21

Brand: Ntron Pages: 29

iTrans 77023554

Brand: Industrial Scientific Pages: 94

Brand: Bahco Pages: 21

Brand: Kübler Pages: 72

AcuRev 1310 Series

Brand: AccuEnergy Pages: 109

Brand: Oberheim Pages: 41

Brand: Newton Pages: 112

Brand: Velleman Pages: 13

Brand: A&D Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands