TLV EF200F-C Instruction Manual Download Page 83

Page: 83 / 181

EF200F-C

Commissioning

Parameter

Prerequisite

Description

Selection / User

entry

Factory setting

Switch-oﬀ delay

• The Switch option is

selected in the Operating
mode parameter.

• The Limit option is selected

in the Switch output
function parameter.

Deﬁne delay for the switch-oﬀ
of status output.

0.0 to 100.0 s

0.0 s

Failure mode

‒

Deﬁne output behavior in
alarm condition.

• Actual status
• Open
• Closed

Open

Invert output signal **

‒

Invert the output signal.

• No
• Yes

Visibility depends on order options or device settings

10.4.7 Configuring the local display

The Display wizard guides you systematically through all the parameters that can
conﬁgured for conﬁguring the local display.

Navigation

"Setup" menu → Display

Display

Format display

Value 1 display

0% bargraph value 1

100% bargraph value 1

Value 2 display

Value 3 display

0% bargraph value 3

100% bargraph value 3

Value 4 display

Switch output isnʼt inverted when “Open” or “Close” is selected for the Failure mode option

►

Summary of Contents for EF200F-C





















































































































































































Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands

TLV EF200F-C, Instruction Manual

Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands