TLV EF200F-C Instruction Manual Download Page 135

Page: 135 / 181

EF200F-C

Diagnostics and troubleshooting

135

Navigation path

Diagnostics → Event logbook → Filter options

Filter categories
• All
• Failure (F)
• Function check (C)
• Out of speciﬁcation (S)
• Maintenance required (M)
• Information (I)

12.7.3 Overview of information events

Unlike a diagnostic event, an information event is displayed in the event logbook only and
not in the diagnostic list.

Info number

Info name

I1000

--------(Device ok)

I1079

Sensor changed

I1089

Power on

I1090

Conﬁguration reset

I1091

Conﬁguration changed

I1092

HistoROM backup deleted

I1110

Write protection switch changed

I1137

Electronic changed

I1151

History reset

I1154

Reset terminal voltage min/max

I1155

Reset electronic temperature

I1156

Memory error trend

I1157

Memory error event list

I1185

Display backup done

I1186

Restore via display done

I1187

Settings downloaded with display

I1188

Display data cleared

I1189

Backup compared

I1227

Sensor emergency mode activated

I1228

Sensor emergency mode failed

I1256

Display: access status changed

I1264

Safety sequence aborted

I1335

Firmware changed

I1397

Fieldbus: access status changed

I1398

CDI: access status changed

I1444

Device veriﬁcation passed

I1445

Device veriﬁcation failed

I1459

I/O module veriﬁcation failed

I1461

Sensor veriﬁcation failed

I1512

Download started

I1513

Download ﬁnished

Summary of Contents for EF200F-C





















































































































































































Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands

TLV EF200F-C, Instruction Manual

Search results

Summary of Contents for EF200F-C

Reviews:

Related manuals for EF200F-C

Brands by name

Popular brands