Terasic Altera DE3 User Manual Download Page 10

Page: 10 / 117

DE3 User Manual

Push-button switches

•

6 push-button switches

1 CPU Reset

1 FPGA Reconfigure

4 user-defined inputs

•

Debounced by a Schmitt trigger circuit

•

Normally high; generates one active-low pulse when the switch is pressed

Slide switches

•

4 slide switches for user-defined inputs

•

When a switch is set to the DOWN or UP position (i.e., close to or away from the edge of

the DE3 board), it causes logic 0 or 1, respectively.

Clock inputs

•

50MHz oscillator

•

1 SMA connector for PLL clock output

•

1 SMA connector for external clock input

USB Host/Slave controller

•

Complies fully with Universal Serial Bus Specification Rev. 2.0

•

Support data transfer at high-speed, full-speed, and low-speed

•

Support both USB host and device

•

Three USB ports (one type mini-AB for host/device and two type A for host)

•

Support Nios II with the Terasic driver

•

Support Programmed I/O (PIO) and Direct Memory Access (DMA)

Eight 180-pin

High Speed Terasic Connectors (HSTC) expansion headers

•

4 male and 4 female connectors are on the top and the bottom of DE3 board, respectively.

•

240 LVDS pairs of user-defined IO pins

•

Configurable I/O voltage for 3.3V, 2.5V, 1.8V, and 1.5V

Two 40-pin expansion headers

•

FPGA I/O pins, as well as 8 power and ground lines, are brought out to two 40-pin

expansion connectors

•

40-pin header is designed to accept a standard 40-pin ribbon cable used for IDE hard drives

•

Share the same I/O pins with HSTC connector A

Summary of Contents for Altera DE3






















































































































Search results

Summary of Contents for Altera DE3

Reviews:

Related manuals for Altera DE3

Brands by name

Popular brands

Terasic Altera DE3, User Manual

Search results

Summary of Contents for Altera DE3

Reviews:

Related manuals for Altera DE3

Brands by name

Popular brands