manualshive.com logo in svg

Telos Zephyr, User Manual

Share
Download
Telos Zephyr User Manual Download Page 117

 Section 7    AUDIO CODING PRINCIPLES

117

audio bandwidth. However, the 32 kHz rate is generally preferred for broadcast
applications because no bits are wasted on frequencies above 15 kHz – which are not
transmitted, anyway.

Layer II primarily operates at 48kHz sample rate. However, the L2 HALF/24 Rcv and
Xmt modes allow operation at 24kHz when this sample rate is desired, primarily when
communicating with “single line” capable Layer II codecs.

Decoder Limitations

•

 

The Layer III decoder in L3 STEREO mode requires that both data channels be
connected and operating to function. Until both channels are present the decoder
will not output anything, even if the Xmt mode at the other end is not stereo.

•

 

If your application requires the ability for the two channels to come and go
independently, such as when they are from independent sites, you must use G.722.
That is the only decode mode which support fully independent operation.

•

 

A typical application which works perfectly within the above constraints is the one
used for dual- language sports broadcasts, with separate studio sites. L III Dual Xmt
mode is used from the stadium to the separate studio sites, while G.722 is used for
the cueing channel from the studios back to the stadium.

Compatibility

Layer II offers compatibility with the widest variety of non- Zephyr equipment. The
Zephyr bitstream is standard ISO format and may be used to communicate with any
codec which supports this standard. In modes which require two ISDN channels, the
channel- splitting (IMUX) method becomes an issue. The Zephyr supports the CDQ
splitting scheme, so it may be used with the codecs from a variety of vendors which
support this mode.

The Zephyr’s G.722 mode offers compatibility with almost all codecs which use this
coding method, and which do not use the rare H.221 framing scheme.

Manual section 8 ( Detailed Menu Reference) has more information about
compatibility, and the Appendix contains a section detailing known non- Telos
equipment compatibility.

Summary of Contents for Zephyr



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands