Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 76 | Manualshive

Page: 76 / 235

Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 76

Getting Started Guide

LM10Zi-GSM-E Rev A

69

Turning on Channels and Traces

Press the front panel

Channel buttons

(1-4). You can also press the

channel buttons on the front of your Acquisition Modules to turn
channels on/off.

OR

From menu bar, choose

Vertical > Channel <#>

.

A trace descriptor box appears on the display for each open channel
trace. When you touch this descriptor box, the trace is activated and the
Channel (C#) dialog opens.

A highlighted descriptor box indicates the active trace to which all
actions apply. Touch this box at any time to open its setup dialog.

NOTE

: The default is to display each trace on its own grid automatically

(Auto Grid). To change how traces are arranged, choose another option
from the Display menu.

You can also quickly create (and turn on the descriptor box for) math
and memory traces without leaving the Channel dialog by touching the
Measure and Math icons at the bottom.

Whenever you activate a channel, math, or memory trace, the dialog at
the bottom of the screen automatically switches to the appropriate
setup dialog for that selection. The tab is labeled with the
corresponding channel number:

«
...
74
75
76
77
78
...
»

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Reviews:

No comments