manualshive.com logo in svg

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 39 / 235

Share
Download
Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 39

LabMaster 10 Zi Oscilloscopes 

32

 

LM10Zi-GSM-E Rev A 

External Display Setup 

Setting up the 

Zi-EXTDISP-15

External Display involves making 

DVI-D

 and 

USB

 connections and some touch screen selections. The USB connection 

is a "hot swap," so there's no need to restart the instrument once 
you've connected. 

1.

 

With your system powered down, attach the 

Zi-EXTDISP-15 

power cord

 from the power port of the PCIe card on the back of 

the Zi-EXTDISP-15 monitor to an AC socket.  

2.

 

Attach the provided 

DVI-D cable

 from the back of the Master 

Control Module to the DVI-D port on the Zi-EXTDISP-15 monitor. 

3.

 

Attach the provided 

USB cable

 (where applicable) from the back 

of the Master Control Module to a USB port on the Zi-EXTDISP-15 
monitor. 

4.

 

Turn on the oscilloscope. 

5.

 

When the instrument has finished booting, touch 

Display → 

Display Setup...

 from the menu bar. 

6.

 

In the 

Second Monitor Configuration

 section of the Display 

dialog, touch 

Open Monitor Control Panel

. 

7.

 

Use the 

Intel® Graphics Media Accelerator Driver

 to adjust 

your external monitor settings.

 

 

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Reviews:

No comments