Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 66 | Manualshive

Page: 66 / 235

Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 66

Getting Started Guide

LM10Zi-GSM-E Rev A

59

A

CTIONS FOR

T

RACE

(S

HORTCUT

)

B

UTTONS

You can access the same functions as the ones produced when using the
Signal Display Grid Pop-Up menu just by clicking a trace-descriptor label,
which shows its corresponding dialog. From the respective dialog,
you're able to access the same functions as Actions for Trace X buttons.



Open the Setup dialog for the trace.



Open the Math dialog for the trace.



Open the Measure dialog for the trace.



Annotate the selected trace.

For more information, see the Actions for Trace Buttons section of

Dialog Area

(on page 61).

A

NNOTATING

T

RACES

The instrument gives you the ability to add an identifying label, bearing
your own text, to a waveform display:

For each waveform, you can create multiple labels and turn them all on
or all off. Also, you can position them on the waveform by dragging or
by specifying an exact horizontal position.

Touch the waveform you want to annotate right on the display grid, and
then touch

Set label...

on the pop-up menu. A dialog box opens in which

«
...
64
65
66
67
68
...
»

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Reviews:

No comments