Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 191

Page: 191 / 235

LabMaster 10 Zi Oscilloscopes

184

LM10Zi-GSM-E Rev A

reconfigure the oscilloscope's connection if it is already
connected to the network or make a new connection.

NOTE

: Your instrument allows you to restrict remote control access to

certain clients. To restrict access, under

Security

, touch the

Yes

button

and enter the IP addresses or domain name server names you want to
restrict separated by a comma.

ONFIGURING THE

EMOTE

ONTROL

SSISTANT

VENT

Under

Remote Control Assistant

, touch inside the

Log Mode

data entry control. Select

Off

Errors Only

, or

Full Dialog

from the

pop-up menu.

Export the contents of the event log to an ASCII text file by
touching the

Show Remote Control Log

button. The

Event Logs

pop-up is shown.

Touch inside the

DestFilename

data entry control and provide a

file name using your preferred input control method. Additional
information on using the touch screen controls can be found in
the

Dialog Area

Then, touch the

Export to Text File

button.

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 191 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: