Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 113

Page: 113 / 235

LabMaster 10 Zi Oscilloscopes

106

LM10Zi-GSM-E Rev A

information on using the touch screen controls can be found in
the

Dialog Area

Provide a voltage level (in millivolts).

NOTE

: Once specified,

Trigger Level

and

Coupling

are the only

parameters remaining unchanged as you switch from trigger mode to
trigger mode for each trigger source.

Optimize for HF

The Optimize for HF checkbox can be used on an

Edge

trigger to reject

high or low frequencies.

The checkbox is marked by default; meaning, the instrument is
optimized for high-frequency waveforms.

NOTE

: If you are measuring a waveform that is 10 MHz or slower, be

sure to unmark the checkbox to avoid triggering on an incorrect slope.

Width Condition

Width

triggers (and other triggers equipped with conditional logic) have

conditional logic settings as follows.

Your

Width Condition

can be specified as

Less Than

Greater Than

Range

and

Out Of Range

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 113 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: