Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 186

Page: 186 / 235

Getting Started Guide

LM10Zi-GSM-E Rev A

179

saved. The file name is assigned automatically and is shown
under the control.

Touch the

Save Now!

button.

Recalling Waveforms

NOTE

: Only .trc files saved in binary format can be recalled into the

oscilloscope.

Access the

Recall Waveform

dialog by either selecting

File → Recall

Waveform

from the menu bar or clicking the

Recall Waveform

button

on the main Save/Recall dialog.

Select either

Memory

File

by touching either respective

button on the

Recall From

portion of the dialog.

Note

: When

Memory

is selected, only

Source

Destination

, and

Show on recall

controls are shown on the Recall Waveform

dialog. When

File

is selected, many more controls are available.

Regardless, the controls are used as explained in the following
steps.

If recalling from Memory, touch inside the

Source

control and

select a source stored in non-volatile RAM (M1–M4) from the

Select Source

pop-up.

Touch inside the

Destination

control and select a location for

storage (memory or file) from M1 to M4.

Show on Recall

- Mark this checkbox to have the memory trace

shown on the grid display after recalling the waveform.

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 186 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: