Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 20

Page: 20 / 235

Getting Started Guide

LM10Zi-GSM-E Rev A

Back of MCM-Zi Master Control Module

Number and Description

ChannelSync Outputs -
SMA 10 GHz Clock and
PCIe 1 Lane Control
Connections (for
corresponding
Acquisition Modules)

10 MHz Reference
Clock Output

10 MHz Reference
Clock Input
(Grounded EMI
Shield required when
port is not in use)

Removable Storage
Drive

AC Power Inlet

The I/O Panel

DVI-D Video
Output

PCIe 4 Lane Data
Inputs (from
corresponding
Acquisition
Modules.

PLEASE NOTE THE FOLLOWING



Cap-off unused

ChannelSync SMA sockets

(item number 1 on the

back of your Master Control Module) using the provided chain-
linked 50 Ω terminations (not shown).



10 MHz Reference Clock Inputs

are specifically intended for

synchronization with other instruments; not between Master
Control Module and Acquisition Modules.



DVI-D Video Output

is for use with an additional external

monitor for Extended Desktop mode.

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 20 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: