manualshive.com logo in svg

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 127 / 235

Share
Download
Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 127

LabMaster 10 Zi Oscilloscopes 

120

 

LM10Zi-GSM-E Rev A 

WaveStream Display Mode 

This fast viewing mode provides brightness-graded intensity 
with a decay time similar to the action of phosphor on an 
analog screen. 

WaveStream mode operates at up to 80 GS/s with an update 

rate of up to several thousand waveforms/second for better capture of 
higher frequency abnormal events. 

Adjusting Trace Intensity 

The 

I

NTENSITY

 knob adjusts the brightness of your trace. 

 

The intensity value is shown in the bottom-right corner of the screen. 

 

Pushing the 

Intensity

 knob changes the Persistence status in the 

following ways.  

 

OFF

 - When the button hasn't been pushed, it may be turned to 

control the trace 

Intensity

 control value. 

 

Analog Persistence

 - When the button is pushed once, the 

waveform resembles a trace on a phosphor oscilloscope. Turning 
the knob affects persistence with a blended form of 

Intensity

 and 

Saturation

. As the knob is turned clockwise, the 

Intensity

 value 

increases while the 

Saturation

 value decreases. The opposite 

occurs when the button is turned counter clockwise. 

 

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Reviews:

No comments