Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 75

Page: 75 / 235

LabMaster 10 Zi Oscilloscopes

LM10Zi-GSM-E Rev A



Label

- Enables you to attach identifying labels to your

waveforms. The labels are preserved when the waveform is
saved as a LabNotebook entry and when saved to file.



Probe Cal - Cable Deskew

- Opens the Probes Cal. dialog where

various Gain, Offset, Skew, Source, and Advanced controls are
available for probe signal calibration.

Another example is seen in the buttons appearing at the bottom of the
Measure

dialogs. The button may be selected in order to display the

functions named on the buttons (sometimes labeled as

Actions

Shortcut buttons on the Fx dialog.

Using these buttons allow you to remain in the Measure dialog while
setting up a Math trace on a parameter measurement.

Message Bar

At the bottom of the oscilloscope display is a narrow message bar. The
current date and time are displayed at the far right. Status, error, or
other messages are also shown in this area.

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 75 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: