Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 185

Page: 185 / 235

LabMaster 10 Zi Oscilloscopes

178

LM10Zi-GSM-E Rev A

PLEASE NOTE THE FOLLOWING



Select

Audio

to save your waveforms into the .wav format.



The

WaveML

format, which enables XML output, is used for

persistence traces.

Vector Signal Analysis (VSA) Support

Users with the VSA Support Software option can choose

With Header

from the

SubFormat

control.

This stores the waveform in

VSA recall

format for later use.

Note

: An Analysis function also comes with the VSA Software which can

send signal traces to VSA as a recording (time domain) file.

You can use the

Auto Save

feature to automatically save a waveform to

disk after each new trigger.

On the

Save Waveform

dialog, touch one of the

Auto Save

buttons.

Select

Wrap

(old files overwritten) or

Fill

(no files overwritten).

CAUTION

Selecting

Fill

can quickly use up all the hard disk

space on your instrument.

Touch the

Browse

button next to the

Save file in directory

control and navigate to the location where you want the file

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 185 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: