Teledyne LabMaster 10 Zi Series Operator'S Manual Download Page 53

Page: 53 / 235

LabMaster 10 Zi Oscilloscopes

LM10Zi-GSM-E Rev A

Basic Controls

Front Panel Control Groupings

Miscellaneous Controls / WaveStream Indicator



Help

- Opens the Teledyne LeCroy Online Assistant. If the second

monitor is installed, the online help opens on the second
monitor.



Default Setup

- Resets the oscilloscope's settings to the default

configuration. Corresponds with screen menu selection:

File →

Recall Setup → Recall Default Setup...

. For a list of default

settings, see

Save/Recall → Saving and Recalling Setups

(on page

173).



Auto Setup

- Opens the

Auto Setup...

flyout menu.

Press the

Auto Setup...

button on the flyout menu to perform a

full auto setup. Press a

Channel Find Scale

button on the flyout

menu to perform a quick auto setup for that channel only. Press
the

UTO

ETUP

...

front panel button twice to perform the last

selection from the

Auto Setup...

flyout menu (the default is to

perform a full auto setup).

If Auto Setup is run when no channels are turned on, all channels
are affected. When more than one channel is turned on, the first
channel with a signal applied to it is automatically set up for edge
triggering.

Summary of Contents for LabMaster 10 Zi Series












































































































































































































































Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews:

Teledyne LabMaster 10 Zi Series, Operator'S Manual, Page: 53 / 235

Search results

Summary of Contents for LabMaster 10 Zi Series

Reviews: