Contents
vi
Figure 3-11: Considerations for custom installation of an instrument.
3–13
. . . . . . . .
Figure 4-1: Simplified representation of the 1730-Series Waveform Monitor.
4–1
. .
Figure 4-2: Simplified block diagram of the Sync Stripper.
4–7
. . . . . . . . . . . . . . . . .
Figure 4-3: Simplified illustration of the Bridge limiter circuit.
4–10
. . . . . . . . . . . . . .
Figure 4-4: Simplified representation of the AFC phase-lock loop.
4–12
. . . . . . . . . . .
Figure 4-5: Elements for line select timing.
Figure 4-6: Relative line select elements for the 2-line display.
4–15
. . . . . . . . . . . . . . .
Figure 4-7: Relative line select timing elements for the 1-line display.
4–16
. . . . . . . . .
Figure 4-8: Timing signals for 1-line and 2-line sweep.
4–17
. . . . . . . . . . . . . . . . . . . . .
Figure 4-9: Z-axis timing for readout.
4–23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-10: Pinout of the CRT Socket
4–30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-1: Remote connector for RGB.
5–5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-2: Remote connector for 90/100 triggering.
5–6
. . . . . . . . . . . . . . . . . . . . . . .
Figure 5-3: Ten full cycles of calibrator signal between timing marks.
5–13
. . . . . . . .
Figure 5-4: Equipment hook–up for checking vertical gain.
5–16
. . . . . . . . . . . . . . . . .
Figure 5-5: Checking PIX MON OUT signal amplitude.
5–18
. . . . . . . . . . . . . . . . . . .
Figure 5-6: Initial equipment setup to check flat response.
5–20
. . . . . . . . . . . . . . . . . .
Figure 5-7: Adjustment locations for the Main and Power Supply boards.
5–29
. . . .
Figure 5-8: Segment of the Main board, showing the test points and adjustment
locations for the +11.8 V supplies.
5–31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-9: Equipment setup to adjust 0.2 ms timing.
5–32
. . . . . . . . . . . . . . . . . . . . . .
Figure 5-10: Equipment setup for adjusting the calibrator amplitude.
5–35
. . . . . . . .
Figure 5-11: Equipment setup for adjusting Channel A input compensation.
5–36
. .
Figure 5-12: Adjusting for best flat response.
5–37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-13: Using the high-range multiburst signal to set flatness.
5–39
. . . . . . . . . .
Figure 6-1: Circuit board assembly locations.
6–5
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-2: Multiple pin connectors used in the 1730–Series Waveform Monitor
.
6–6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-3: Bezel removal.
6–17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-4: Rear panel securing screws.
6–19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-5: Screws that hold the Front Panel circuit board (A2) in place.
6–21
. . . . .
Figure 6-6: Screws holding the Main circuit board (A3) in place.
6–22
. . . . . . . . . . . .
Figure 6-7: Screws holding the Power Supply circuit board (A1) in place.
6–23
. . . . .
Figure 6-8: Repackaging a 1730–Series instrument.
6–24
. . . . . . . . . . . . . . . . . . . . . . .
Summary of Contents for 1730 Series
