48 / 188
d. After placing an oil pan under the oil drain bolt, use a
14# sleeve to remove the oil drain bolt
⑶
and the combined
seal gasket
⑷
. Use a 24# sleeve to remove the strainer cover
⑸
at the bottom, take off the 34.5×3.5 acrylate rubber O-
ring
⑹
, the φ25.8×34.2×1.8 strainer spring
⑺
and the outer
diameter φ22×21 cap
-shaped strainer
⑻
. Drain the oil from
the crankcase.
e. Check whether the strainer
⑻
is damaged, if it is
damaged, replace it, if not, clean it up.
f. Wipe clean the joint surface with a non-woven fabric.
Inspect the oil drain bolt
⑶
whether the joint surface is
scratched; if there is any, replace it with a new one, if not,
wipe it clean.
g. Replace the new combination gasket
⑷
, and use a 14#
sleeve to install the oil drain bolt
⑶
and combination gasket
⑷
back to the engine box. Torque: 25N.m (2.6 kgf.m, 18 lbf.
ft). Replace the new O-ring
⑹
, put the O-ring
⑹
, spring
⑺
and cap-type fine filter
⑻
into the fine filter cover
⑸
in
turn, and then put it back to the bottom of the engine with a
24# sleeve.
2. Replace fine filter
a. Place an oil pan under the fine filter cover.
b. Use a 10# sleeve to loosen the 3 nuts
⑴
at the fine filter
cover.
c. Remove the fine filter cover
⑵
and O ring (3a). Remove
the spring
⑷
, the fine filter (oil filter element) (3b) and the
gasket (3c) in sequence.
d. Replace the new fine filter (oil filter element) and
gasket. The fine filter assembly already contains O ring (3a),
fine filter (oil filter element) (3b) and gasket (3c). Replace in
order.
e. Remove the O ring on the fine filter cover and replace it
with a new O ring. First put the O ring (3a) into the groove of
the fine filter cover
⑵
, and then install it back to the engine
box.
f. Screw back the 3 nuts (1), Torque: 12 N.m (1.2 kgf.m, 9
lbf.ft).
3. Add oil
a. Replace the filter element with a measuring cup with a
viscosity of SAE5W-40/10W-40/10W-50. The new API SN
grade or higher motorcycle special machine 0.95L (1 US qt,
0.84 lmp qt, 0.25 US gal, 0.21 lmp gal). If the filter element is
not replaced, the measuring cup is filled with 0.9L (0.95 US
qt, 0.79 lmp qt, 0.24 US gal, 0.2 lmp gal).
b. Use a measuring cup to add engine oil to the
fuel filler opening on the right crankcase cover of the engine.
c. Wipe clean the fuel filler opening with a non-woven
cloth.
d.inspection O ring
⑵
Whether there is damage or aging, if
not, wipe it clean, if any, replace it.
e. Wipe clean the oil dipstick, and turn the oil dipstick
⑴
and O-ring
⑵
clockwise by hand to replace the right
crankcase cover of the engine.
Summary of Contents for ZONTES 310T-M 2022
