manualshive.com logo in svg

Taylor C832, Service Manual

Share
Download
Taylor C832 Service Manual Download Page 9

 3

McDonald's Intelligap Grills

Introduction

 This unit has many sharp edges that can

cause severe injuries.

This unit must 

NOT

 be installed in an area

where a water jet or hose can be used. 

NEVER 

use a water jet or hose to rinse or clean the

unit. 
Failure to follow these instructions may result in
electrocution, burns from hot steam, or liquid
collecting inside the grill and destroying electrical
components.

 This grill must be placed on a level surface.

Failure to comply may result in personal injury or
equipment damage.

S

DO NOT

 store flammable vapors, liquids, or

combustible material in the vicinity of the
grill.

S

Appropriate grill clearance must be
maintained.

Failure to comply could result in a fire hazard.

NOISE LEVEL:

 Airborne noise emission does not

exceed 70 dB(A) when measured at a distance of
1.0 meter from the surface of the machine and at a
height of 1.6 meters from the floor.

Summary of Contents for C832




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands