manualshive.com logo in svg

Taylor C832, Service Manual

Share
Download
Taylor C832 Service Manual Download Page 19

 13

McDonald's Intelligap Grills

Introduction

150520

Model C845 Specifications

See the data label for exact specifications.

Electrical

Standard is 208/60/3 phase.

Two dedicated electrical connections are required;
one, three phase and one interlock/control single
phase. See the electrical chart for the proper
electrical requirements. Manufactured to be
permanently connected. Consult your KES or local
Taylor distributor for cord and receptacle
specifications as local codes allow.

Electrical

Total

Amp

Total

KW

Interlock/

Control
Voltage

Interlock

Fuse

Size

208/60/3

22

7.8

120/60/1

10A

200/50/60/3

23

7.8

100/50/60/1

10A

220/380/60/3

12

7.8

230/60/1

10A

220/50/60/3

20

7.8

220/60/1

10A

400/50/3n~4w

11

7.8

230/50/1

10A

Gas

Three ceramic infrared burners: 25,000 BTUH each.
Manifold pressure: 3.5” w.c. natural, 10.5” w.c.
propane.

Dimensions

Width: 38” (965 mm)
Depth: 38-1/2” (978 mm)
Height : 50-1/2 to 55-1/2” (1283 to 1410 mm)
Cooking Surface Height: 29 to 34” (737 to 864 mm)
Floor Clearance: 3-3/4 to 8-3/4” 
(96 to 223 mm) (Casters may be adjusted.)

Approximate Weight

Net: 923 lbs. (418.7 kgs.)

Crated: 1032 lbs. (468.1 kgs.)

Volume

52.6 cu. ft. (1.49 cu. m.)

Figure 8 

Summary of Contents for C832




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands