Taylor C832 Service Manual Download Page 56

Page: 56 / 219

Controls and Systems

McDonald's Intelligap Grills

140922

Software Loading Procedures

IMPORTANT: After loading new software, the
gap, volume, and temperature settings will be at
the default factory settings.

Step 1
Record the present settings for system setup
and key menu items.

a. Turn the Fan Interlock Switch to the ON position.

b. While “OFF” is displayed, press the

key

and enter the Service Menu passcode.

c. Press the

key until “SYSTEM SETUP” is

displayed.

d. Press the

key. The display will read

“PROBE CALIBRATION/TOP BACK.”

e. Record the offset.

f. Press the

key to display “PROBE

CALIBRATION/TOP FRONT.”

g. Record the offsets.

h. Repeat until all offsets are recorded and then

press the

key.

Press the

key until the screen displays

“GAP CALIBRATION.”

Document the settings for the right side.

k. Press the

key to go to the front and left

sides. Document all settings.

Step 2
Download the new software.

a. Place the Fan Interlock Switch in the OFF

position.

b. Remove the screw on the right and left edge of

the lower front panel to allow the panel to swing
down.

c. Loosen one screw on the back of the control to

allow the access door to swing open.

d. Insert the program module into the receptacle

located under the door. (See Figure 41.)

e. Swing the lower front panel up to view the

display.

Figure 41

Summary of Contents for C832




























































































































































































































Search results

Summary of Contents for C832

Reviews:

Brands by name

Popular brands

Taylor C832, Service Manual

Search results

Summary of Contents for C832

Reviews:

Brands by name

Popular brands