manualshive.com logo in svg

Taylor C832, Service Manual

Share
Download
Taylor C832 Service Manual Download Page 54

 48

Controls and Systems

McDonald's Intelligap Grills

140922

Enabling LonWorks® Gateway

IMPORTANT!  The Gateway must be enabled on
all three control panels. Repeat the following
steps for each control panel.

Step 1

While in the AM/PM Mode, access the Control Menu

by pressing the 

 key to display

“PROGRAMMING.”

Step 2

Press the 

 key to display the passcode entry

screen.

Step 3

Enter the Control Menu passcode by pressing the
keys in this order:

Step 4

Press the 

 key repeatedly until “SYSTEM SET

UP” displays.

Step 5

Press the 

 key to scroll to “GATEWAY

ENABLED Y or N” (YES or NO).

Step 6

Press the 

 key to change to “Y” (YES).

Step 7

Press the 

 key.

Step 8

Press the 

 key.

Step 9

Press the 

 key to exit the programming mode.

Step 10
Repeat Steps 1 - 9 to enable the Gateway on the
second and third control panels.

Step 11

Shut off the grill for 30 seconds before attempting to
send a service pin.

Sending Service Pin From Menu

Step 1

While in the AM/PM Mode, access the Control Menu

by pressing the 

 key to display

“PROGRAMMING.”

Step 2

Press the 

 key to display the passcode entry

screen. (

Note:

 No passcode is required. Proceed to

the next step.)

Step 3

Press 

 key until the SOFTWARE VERSION is

displayed.

Step 4

Press the 

 key until the GATEWAY VERSION

number appears.

Note:  

If question marks appear instead of the

Gateway version number, wait a few seconds. If the
version number does not appear, shut the machine
off. After approximately 30 seconds, restart the
machine and repeat Steps 1 - 4.

Step 5

Press the 

 key to send the service pin.

Step 6

Press the 

 key.

Step 7

Press the 

 key to exit the programming mode.

Summary of Contents for C832




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands