Taylor C832 Service Manual Download Page 57

Page: 57 / 219

McDonald's Intelligap Grills

Controls and Systems

140922

f. Turn the Fan Interlock Switch to the “ON”

position.

g. While “OFF” is displayed, press the

key

and enter the Service Menu passcode.

h. Press the

key until “SOFTWARE

VERSIONS” is displayed.

Press the

key until the display flashes

“Software Versions on PGM Module Chip X”.

Press the

key to start the download.

k. If the

key was pressed while the display

flashed “Software Versions on PGM Module Chip
1”, the display will show a count-up sequence.

If the

key was pressed while the display

flashed “Software Versions on PGM Module Chip
2”, the display will go blank for one or two
minutes while the software is loaded. The other
displays will remain on.

DO NOT TURN THE

INTERLOCK SWITCH OFF.

When the software download is complete, “OFF”
will be displayed.

m. Turn the Fan Interlock Switch to the “OFF”

position.

n. Remove the program module and secure the

access door on the control.

o. Swing the lower front panel up and secure it.

Step 3
Re-program the control, using the previously
recorded settings.

a. After entering the gap settings, make sure to

save and auto-level the platens.

b. Verify the temperature and gap settings.

Step 4
Program the correct date and time.

Summary of Contents for C832




























































































































































































































Search results

Summary of Contents for C832

Reviews:

Brands by name

Popular brands

Taylor C832, Service Manual

Search results

Summary of Contents for C832

Reviews:

Brands by name

Popular brands