Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 40 / 113

2-30

Emerald ICE Deluxe Telephone User Guide

e S

Feature Code:

PGM

p#3

Description

Emerald ICE

Deluxe Telephones have 28 dual-colored programmable Feature/DSS

Buttons. You can program any system feature code on any Feature/DSS Button for
one-button operation. Certain programmed Feature/DSS Buttons will light when
activated (

Do Not Disturb

, Call Forward, DSS/BLF, etc.), while others such as Call

Pick-Up, Background Music, Last Number Redial, do not.

Features are separated into two distinct categories for programming onto Flexible
Buttons: Directory Numbers or Feature Codes.

1. While the phone is idle, press

PGM

p#3

. The display indicates that

you are in Feature button programming mode by prompting you to press a
key:

2. Press the Feature/DSS Button that you want to program. The current

programming displays:

3. Press

[chg]

. The following will be displayed.

4. To program the button, you must know the code type. Use

Feature/Directory/Suffix Code Lookup

(Refer to

Section

2.17

) to locate the

feature and code you want to program.

a. To program a directory number, press

[dir]

b. Enter the appropriate directory number and then press

[save]

. If

you make a mistake, use

[bksp]

and

[chg]

to re-enter the number.

2.18

Feature/DSS Button Programming

PRESS FTR KEY

P4____
show chg

SELECT FUNCTION
dir pgm

DIR NUMBER :_
bksp save chg

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands