Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 47 / 113

Emerald ICE Deluxe Telephone User Guide

2-37

e S

Invoke Hotline

1. While the telephone is idle, lift the handset or press the

button. A call

is placed to the selected destination either immediately or after the delay
time.

2. Hang up to finish the call.

Operational Notes

•

If delay mode is selected other calls can be placed during the delay period.

•

The Hotline feature code

PGM

p9*

can be programmed on an available

Feature/DSS Button.

Feature Code:

PGM

p98

Description

A Deluxe Telephone has the benefit of receiving intercom calls in three ways:

•

Voice Announce Hands-free reply mode

•

Voice Announce Privacy Mode

•

Tone Ringing Mode

The Status Bar Lamp and Feature/DSS Button (if programmed) will indicate:

2.23

Voice Announce

Mode

Button
Lamp

Momentary
Confirmation

Confirmati
on Tone
Heard

Status Bar
(when intercom
call rec’d)

Voice
Announce
–
Handsfree

Green LED

VA-HF MODE

single burst
tone

Solid Red LED

Voice
Announce
– Private

Red LED

VA-PRIVACYMODE

single burst
tone

Slow Flashing Red
LED

Tone Ring
Mode

No LED lit

TONE RING MODE

single burst
tone

Fast Flashing Green
LED

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands