Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 42 / 113

2-32

Emerald ICE Deluxe Telephone User Guide

e S

Feature Code:

PGM

p9#

Description

The Deluxe Telephone has a standard 2.5 millimeter headset jack. When

Headset

Mode

is selected the

button is used to activate/deactivate the headset.

Activate Headset Mode

1. While the telephone is idle, press

PGM

p9#

or press the Feature/DSS

Button designated as HEADSET MODE (if programmed). The display
indicates the new status:

Deactivate Headset Mode

1. While the telephone is idle, press

PGM

p*9#

or press the

Feature/DSS Button programmed with the

Headset Mode

code (if

programmed). The display indicates the new status:

Use the Headset to Place a Call

1. While the telephone is idle, press

, a DSS button, or outside line

button. The

button LED flashes to indicate that the headset is active.

You hear Intercom dial tone, outside line dial tone, or Intercom ring-back
tone, depending on the function invoked.

2. Press

again to disconnect the current call.

2.19

Headset Mode

HEADSET ENABLED

HEADSET DISABLED

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands