Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 87 / 113

Emerald ICE Deluxe Telephone User Guide

4-9

Cal

ling

Featur

Feature Code:

PGM

Description

The One-Time

Do Not Disturb

feature allows you to block outside line ringing

while engaged in a call. The feature will automatically be disabled at the end of
the current call.

1. While you are connected with a call and a new call rings at your extension.

To cancel ringing for this call, press a pre-programmed Feature/DSS Button
designated as DO NOT DISTURB or press

PGM

Do Not Disturb (One Time

) is activated.

Do Not Disturb (One Time

) will deactivate when the current call is

disconnected.

Operational Notes

•

The

Do Not Disturb (One Time

) feature code may be programmed on a Fea-

ture/DSS Button.

•

A Feature/DSS Button programmed for the

Do Not Disturb

code will flash at

a fast rate while

Do Not Disturb (One Time

) is active.

4.7

Do Not Disturb (One Time)

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands