Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 111 / 113

Emerald ICE Deluxe Telephone User Guide

4-33

Cal

ling

Featur

Feature Code:

PGM

p72

Description

The

Help Mode

feature is available to assist you with operating instructions for all

Emerald ICE

features. A Voicemail module must be installed and operating for this

feature to operate.

1. Press the factory programmed HELP Feature/DSS button on the Deluxe

Telephone or enter

PGM

p72

. You will be prompted to press a

programmed Features/DSS button for help with the feature that you need
help with. The display will show:

2. Press the Feature/DSS button for the feature that you need help with.

Adjust the volume with the

button if necessary.

Operational Notes

•

Emerald ICE

Voicemail module must be installed on the KSU and operat-

ing for

Help Mode

to operate.

•

If a CO line button is pressed or an extension button is pressed, the

Help

Mode

will recite the line or extension number that was pressed.

4.27

Help Mode

HELP MODE

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands