Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 48 / 113

2-38

Emerald ICE Deluxe Telephone User Guide

e S

Setup

1. While your extension is idle, press

PGM

p98

. You hear a confirmation

tone and the display indicates the new mode set:

2. Press

PGM

p98

again to advance through each of the available modes.

Receiving a Call in VA-HF Mode

When your extension is idle, you will be alerted of intercom calls by one tone
burst. The voice connection is then established immediately and you can respond
to the calling extension via the speakerphone.

Receiving a Call in VA-Privacy Mode

1. When your extension is idle, you will be alerted of an intercom call by one

tone burst. The voice connection is then established immediately with the

Mute

function activated at your extension. You hear the calling extension

voice announcement over the speaker, but the microphone in your
telephone is disabled.

2. You

can:

a. Lift the handset for privacy.

b. Press the

button to deactivate the

Mute

feature and speak with the

caller using the speakerphone.

Receiving a Call in Tone Mode

1. When your extension is idle, you will be alerted of an intercom call by a

double-burst tone which is repeated until you respond or until the call
follows a

Call Forward

route.

2. You

can:

a. Lift the handset for privacy.

VA-PRIVACY MODE

VA-HF MODE

TONE RING MODE

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands