Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 17 / 113

Emerald ICE Deluxe Telephone User Guide

2-7

e S

3. To record this greeting, press the softkey beneath

show

. The display will

show:

is the current time allotted to this message.

a. To change the total length allotted to this message, press the softkey

beneath

chg

. Enter the new time in seconds (

) then

press the softkey beneath

save

b. Press the softkey beneath

play

to hear the current contents of this

greeting/message. The display shows:

This indicates that you will hear the recorded greeting for the first

port. There are four ports-each recorded simultaneously during the
“record” operation. You may use the the softkey beneath

chg

function

to playback each individual port to test each for proper operation.

c. Press the softkey beneath

record

to begin recording this greeting.

Once the softkey beneath

record

has been pressed, the record

operation is immediately begun.

The length of the message/greeting to be recorded cannot exceed the
allotted time length for this greeting/message.)

d. Press the softkey beneath

stop

to end the recording of this message.

If the Record Time is exceeded, the record operation will end automatically.

e. Press the

button to return to the previous level of setup. (

1.DAY

GREETING

) To skip to the next greeting/message, press the softkey

beneath

. The display will show:

RECORD TIME :XX
back next show

AUTO_ATT NO. :1
back next show

2.ALT GREETING
back next show

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands