Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 88 / 113

4-10

Emerald ICE Deluxe Telephone User Guide

Cal

ling

Featur

Description

The

Do Not Disturb

–

Override

feature allows you to override the

Do Not Disturb

condition at another extension.

Do Not Disturb-Override

is available only if

Intrusion (

Section 4.16

)

is active on the

calling extension.

Calling an Extension in Do Not Disturb

1. Place

intercom

call to the extension in

Do Not Disturb

. You will hear

Do Not

Disturb

tone and the display indicates the condition of the called extension:

2. Press

the softkey beneath

override]

3. The called extension begins to ring.

Operational Notes

•

An extension in

Do Not Disturb

that has been override may invoked

Forced

Intercom Call Forward

.(Refer to

Section 4.10

)

•

The

Do Not Disturb

feature code may be programmed on a programmable

Feature/DSS Button.

4.8

Do Not Disturb (Override)

EXT 403 DND
override

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands