Tadiran Telecom Emerald ICD Deluxe User Manual Download

Page: 75 / 113

Emerald ICE Deluxe Telephone User Guide

3-15

Maki

ng Ca

lls

Description

You can make outgoing calls from your Deluxe Telephone using the speakerphone.
The

button LED is lit when you are making a call.

1. dial any extension number directly from the keypad without lifting the

handset. The

Hotkey

feature must be active.

Or…

2. Press any outside line button and dial without lifting the handset.

3. When Hot Key is disabled, press the

button or press an idle outside

line button then dial without lifting the handset.

Operational Notes

N/A

Feature Code:

200

208

820

Description

You can make a public announcement to all extensions or to a group of extensions.
The

Emerald

ICE

system provides both all-call (heard by all users) and page zone

(heard by a specific group of users). Page announcements are heard over the
extension speakers.

1. While in the idle condition – lift the handset.

2. Dial

the

Zone Page

access code (extensions)

201

–

208

for

extensions or

820

for external page. Press the Feature/DSS Button

designated as

All Call Page

or dial the

All Call Page

access code

200

You hear the Page Alert Tone.

4. Make a paging announcement.

5. Hang up when finished.

3.11

On-Hook Dialing

3.12

Paging

Summary of Contents for Emerald ICD Deluxe


















































































































Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands

Tadiran Telecom Emerald ICD Deluxe, User Manual

Search results

Summary of Contents for Emerald ICD Deluxe

Reviews:

Related manuals for Emerald ICD Deluxe

Brands by name

Popular brands