manualshive.com logo in svg

Synxcom SM9234D, User Manual

Share
Download
Synxcom SM9234D User Manual Download Page 70

AT Commands 

Page 70 

 

Response: 

+ILRR: (<value> range) 

Example: 

+ILRR: (0,1) 

 

 

Reported Rate

 

The <rate> reported represents the current (negotiated or renegotiated) DTE-
modem rate. If enabled, the intermediate result code is transmitted after any 
modulation, error control or data compression reports are transmitted, and before 
any final result code (e.g., CONNECT) is transmitted. The <rate> is applied after 
the final result code is transmitted. 
The DTE-modem port rate will change only if neither buffered mode nor error 
controlled means are enabled (+ES=x,0) and if the negotiated carrier rate (+MRR) 
does not match the current DTE-modem port rate (auto-detected from the previous 
command line). 
Syntax 

+ILRR: <rate>[,<rx_rate>] 

Defined Values 

 

<rate>  Decimal value representing Decimal value representing the 

current (negotiated or renegotiated) DTE-modem rate: 

0-9, 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 
115200, or 230400 

<rx_rate>  Optional decimal value reporting the RXD rate, if it is 

different from the TXD rate: 

0, 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 
115200, or 230400 

Example: 

+ILRR: 19200 

Call Control 

D - Dial 

This command directs the modem to go on-line, dial according to the string 
entered and attempt to establish a connection. If no dial string is supplied, the 
modem will go on-line and attempt the handshake in originate mode. 

NOTE: If the ATD command is issued before the S1 register has cleared, the 
modem will respond with the NO CARRIER result code. 

If +FCLASS=0 is selected, the modem will behave as a data modem and will 
attempt to connect to another data modem. The modem will have up to the period 
of time specified by register S6 or S7 to wait for carrier and complete the 
handshake. If this time expires before the modem can complete the handshake, the 
modem will go on-hook with the NO CARRIER response. This command will be 
aborted in progress upon receipt of any DTE character before completion of the 
handshake. 

If +FCLASS=1, 1.0, or 2 is selected, the modem will behave as a facsimile modem 
and attempt to connect to a facsimile machine (or modem) by entering the HDLC 
V.21 channel 2 receive state (as if +FRH=3 had been issued). This command will 
be aborted upon receipt of any DTE character if the modem has not finished 

dialing. In this case, the modem will go on-hook and return to command mode after displaying 

Summary of Contents for SM9234D

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands