manualshive.com logo in svg

Synxcom SM9234D, User Manual

Share
Download
Synxcom SM9234D User Manual Download Page 135

AT Commands 

Page 135 

 

S48 - V.42 Negotiation Control 

The V.42 negotiation process determines the capabilities of the remote modem. 
However, when the capabilities of the remote modem are known and negotiation is 
unnecessary, this process can be bypassed if so desired. 

Range:    

0, 7, or 128 If an invalid number is entered, it is accepted into 

the S-Parameter, but S48 will act as if 128 has been entered.

 

Default:  7

 

 

S48=0   Disable negotiation; bypass the detection and negotiation 

phases; and proceed with LAPM.

 

S48=7   

Enable negotiation. (Default.) 

 

S48=128 

Disable negotiation; bypass the detection and 

negotiation phases; and proceed at once with the fallback action specified in 
S36. Can be used to force MNP.

 

S86 - Call Failure Reason Code 

When the modem issues a NO CARRIER result code, a value is written to S86 
Register to help determine the reason for the failed connection. S86 records the 
first event that contributes to a NO CARRIER message. The code definitions are: 

Range:   

0-26

 

Default:  

21

 

S86=0  Normal hangup, no error occurred.

 

S86=1  Reserved.

 

S86=2  Reserved.

 

S86=3  Call Waiting caused disconnect.

 

S86=4  Physical carrier loss.

 

S86=5  No error correction at the other end.

 

S86=6  No response to feature negotiation.

 

S86=7   This modem is async only; the other modem is sync only.

 

S86=8  No framing technique in common.

 

S86=9  No protocol in common.

 

S86=10 Bad response to feature negotiation.

 

S86=11 

No sync information from the remote modem. 

S86=12 Normal hangup initiated by the remote modem.

 

S86=13 Retransmission limit reached.

 

S86=14 Protocol violation occurred.

 

S86=15 Lost DTR.

 

S86=16 Received GSTN cleardown.

 

S86=17 Inactivity timeout.

 

S86=18 Speed not supported.

 

S86=19 Long space disconnect.

 

S86=20 Key abort disconnect.

 

S86=21 Clears previous disconnect reason.

 

S86=22 No connection established.

 

S86=23 Disconnect after three retrains.

 

S86=24 Call Waiting tone detected.

 

S86=25 Extension pickup detected.

 

Summary of Contents for SM9234D

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands