Synxcom SM9234D User Manual Download Page 116

Page: 116 / 216

AT Commands

Page 116

:E - Compromise Equalizer Enable Command

This command is included for compatibility only and has no effect other than
returning a result code.

Syntax

:E<value>

Defined Value

<value> Decimal number corresponding to the selected option.

0 :E0 command.

1 :E1 command.

30 @M30 command.

Result Codes

OK 0 or 1.

ERROR Otherwise.

FastConnect Commands

$F – FastConnect Control

This command allows configuring of the client modem to connect to a central site
modem that supports non-standard V.22 and V.22bis FastConnect protocols.

Syntax

$F<n>

Defined Value

<n> Decimal number which specifies the initial requested mode of

operation when the modem is operating as the originator. The
options are:

0 Normal connection (Default)

1 FastConnect without answer tone

2 Reserved

3 FastConnect with answer tone

Result Codes

OK 0 or 1.

ERROR Otherwise.

Summary of Contents for SM9234D

























































































































































































































Search results

Summary of Contents for SM9234D

Reviews:

Brands by name

Popular brands

Synxcom SM9234D, User Manual

Search results

Summary of Contents for SM9234D

Reviews:

Brands by name

Popular brands