Synxcom SM9234D User Manual Download Page 129

Page: 129 / 216

AT Commands

Page 129

S16 - Test Mode Bit Mapped Options Status

S16 indicates the test in progress status.

Default:

Bit 0

Local analog loopback

0 =

Disabled (Default.)

1 =

Enabled (&T1)

Bits 1-7

Not used

S19 – Reserved

S19 is supported for backwards compatibility only. No value can be written.
Responds with default value.

Range:

None

Default :

S20 – Reserved

S20 is supported for backwards compatibility only. No value can be written.
Responds with default value.

Range:

None

Default:

S21 - V.24/General Bit Mapped Options Status

S21 indicates the status of command options.

Default:

52 (34h) (00110100b)

Bits 0-1 Reserved (0)

Bit 2

CTS behavior (&Rn)

0 =

CTS tracks RTS (&R0)

1 =

CTS always on (&R1) (Default.)

Bits 3-4

DTR behavior (&Dn)

0 =

&D0 selected

1 =

&D1 selected

2 =

&D2 selected (Default.)

3 =

&D3 selected

Bit 5

RLSD (DCD) behavior (&Cn)

0 =

&C0 selected

1 =

&C1 selected (Default.)

Bit 6

DSR behavior (&Sn)

0 =

&S0 selected (Default.)

1 =

&S1 selected

Bit 7

Long space disconnect (Yn)

0 =

Y0 (Default.)

1 =

Summary of Contents for SM9234D

























































































































































































































Search results

Summary of Contents for SM9234D

Reviews:

Brands by name

Popular brands

Synxcom SM9234D, User Manual

Search results

Summary of Contents for SM9234D

Reviews:

Brands by name

Popular brands