![Synxcom SM9234D User Manual Download Page 110](http://html1.mh-extra.com/html/synxcom/sm9234d/sm9234d_user-manual_1421424110.webp)
AT Commands
Page 110
Table A-4. AT#UD Last Call Status Report Format
Key
Value(s)
Definition
0
2 digits
Diagnostic Command Specification revision number, digit.digit
1
Table 3-5
Call Setup Result code
2
Table 3-6
Multi-media mode
3
Table 3-7
DTE-DCE interface mode
4
String
V.8 CM octet string, same format as V.250, in quotes
5
String
V.8 JM octet string, same format as V.250, in quotes
10
0-2F
Received signal power level, in –dBm (0-43)
11
0-1F
Transmit signal power level, in –dBm (e.g., 0-17)
12
0-64
Estimated noise level, in –dBm (e.g., 10-90)
17
0-FFF
Round Trip delay, in units of ms
18
Table 3-8
V.34 INFO bit map
20
Table 3-9
Transmit Carrier Negotiation Result
21
Table 3-9
Receive Carrier Negotiation Result
22
0-1F40
Transmit Carrier symbol rate (0-8000) in symbol/s
23
0-1F40
Receive Carrier symbol rate (0-8000) in symbol/s
24
0-FA0
Transmit Carrier frequency (0-4000) in Hz
25
0-FA0
Receive Carrier frequency (0-4000) in Hz
26
0-FA00
Initial transmit carrier data rate (0-64000) in bit/s
27
0-FA00
Initial receive carrier data rate (0-64000) in bit/s
30
0-FF
Temporary carrier loss event count
31
0-FF
Carrier Rate re-negotiation event count
32
0-FF
Carrier Retrains requested
33
0-FF
Carrier Retrain requests granted
34
0-FA00
Final transmit carrier data rate in bit/s
35
0-FA00
Final receive carrier data rate in bit/s
40
Table 3-10
Protocol Negotiation Result
41
0-400 Error
Control frame size in bytes
42
0-FF
Error control link timeouts in transmission
43
0-FF
Error control link NAKs received
44
Table 3-11
Compression Negotiation Result
50
0-2
Transmit flow control: 0 = off; 1 = DC1/DC3; 2 = V.24 circuit
106/133
51
0-2
Receive flow control: 0 = off; 1 = DC1/DC3; 2 = V.24 circuit
106/133
52
0-FFFFFFFF Transmit characters sent from DTE
53
0-FFFFFFFF Received characters sent to DTE
54
0-FFFF
Transmit characters lost (data overrun errors from DTE)
55
0-FFFF
Received characters lost (data overrun errors to DTE)
56
0-FFFFFFFF Transmit I- Frame count, if error control protocol running
57
0-FFFFFFFF Received I-Frame count, if error control protocol running
58
0-FFFF
Transmit I-Frame error count, if error control protocol running
59
0-FFFF
Received I- Frame error count, if error control protocol running
60
Table 3-12
Termination Cause
61
0-FF
Call Waiting event count
Summary of Contents for SM9234D
