manualshive.com logo in svg

Synxcom SM9234D, User Manual

Share
Download
Synxcom SM9234D User Manual Download Page 175

AT Commands 

Page 175 

 

+FDT - Data Transmission 

Syntax: +FDT <CR> 

The +FDT command prefixes Phase C data transmission. When the DCE is ready 
to accept Phase C data, it issues the negotiation responses and the CONNECT 
result code to the DTE. 

In Phase B, the +FDT command releases the DCE to proceed with negotiation, 
and releases the DCS message to the remote station. In Phase C, the +FDT 
command resumes transmission after the end of a prior transmit data stream. 

Initiate Page Transmission 

Phase B DCE polled response: 

 

[+FCSI:<remote ID string>] - 

 

 if new CSI received

 

 

[+FDIS:<subparameters from remote station>] -  if new DIS received

 

 

+FDCS:<T.30 subparameter string>

 

 

CONNECT

 

 

<XON> - 

 

 

 

 when ready for data

 

After placing a call, or after finishing a document exchange, the DTE may 
command the DCE to re-enter T.30 Phase B to attempt to negotiate a document 
transmission. 

Continue a Page 

 

CONNECT

 

 

<XON>

 

The DTE may issue more than one +FDT command for a given page, so that 
different files may be concatenated together. These files must have the same 
format. 

Phase C Data Framing 

Phase C data must be presented to the DCE in stream mode. The DCE expects 
Phase C data to follow until it detects <DLE><ETX> termination characters. The 
DCE will filter the stream, as described later in this appendix. 

The DCE will acknowledge the end of the data by returning the OK result code to 
the DTE. 

If there is data underrun before the next +FDT or +FET= command, the DCE will 
zero-fill the pad as per T.4 until the Phase C timeout (+FPHCTO) is reached, or 

Summary of Contents for SM9234D

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands