manualshive.com logo in svg

Synxcom SM9234D, User Manual

Share
Download
Synxcom SM9234D User Manual Download Page 210

AT Commands 

Page 210 

 

Response: 

(<enable> range),(<report>range) 

Example: 

(0,1),(0-6)

 

Result Codes 

 

OK  <enable>,<report> = (0,1),(0-6) 

ERROR  Otherwise, or if not in Voice Mode. 

+VDT - Control Tone Cadence Reporting 

This command is included for compatibility only and has no effect other than 
returning a result code. 

This command allows the modem to enable or disable reporting of the control tone 
cadence information in the frequency band used by the Ringback/Remote Ring, 
BUSY, and reorder/Fast Busy tones (usually in the 300 to 600 Hz range). 

Syntax 

+VDT=<enable>,<report>

 

Defined Values 

 

<enable>

 

Decimal number corresponding to the selected option.

 

 

0  The modem will not produce any control tone 

cadence report. 

<report>

 

Decimal number specifying the produced any control tone 
cadence report when enabled by the <enable> subparameter.

 

 

0  The modem will produce only CPOF and CPON 

messages. 

 

Other  Reserved. 

Reporting Current or Selected Values 
Command: 

+VDT? 

Response: 

<enable>,<report> 

Example: 

0,0 

 

 

For the default setting. 

Reporting Supported Range of Parameter Values 
Command: 

+VDT=? 

Response: 

: (<enable> range),(<report> range) 

Example: 

(0),(0)

 

Result Codes 

 

OK  <enable>,<report> = (0),(0) 

ERROR  Otherwise, or if not in Voice Mode. 

+VPR - Select DTE/Modem Interface Rate (Turn Off Autobaud) 

This command selects the DTE/modem interface rate. 

Syntax 

+VPR=<rate>

 

Defined Values 

 

<rate>

 

Decimal number corresponding to the DTE/modem interface 
rate where  = autobaud rate determined by processing the AT 
command, and 1,2,3,4,8,16,24,48,96 correspond to multipliers 
of 2400 bps to determine the actual rate:

 

Summary of Contents for SM9234D

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands