Strack Z7510 Operating Instruction Download Page 66

Page: 66 / 70

Operating instruction Z7510 Multizone temperatur controller

Temperatur controller

STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de

08.2018

Operations manual NR4000-v.2

Profibus DP interface

STRACK

multizone controllers of the

NR4000

series can be equipped with a Profibus-DP-

interface according to EN 50170.

Interface:

RS485

Twisted pair 2-wire con-

nection. see EN 50170,

Chapt. 2

Network-

Linear bus system with active bus

Topology:

termination on both ends.

Spot lines are possible (depending

on the used cable type):

3-12Mbit/sec. = max. lenght : 1,5m

1,5Mbit/sec. = max. lenght : 6,5m

Baud rate and wiring lenght (without repeater):

The baudrate will be detected by

the Profibus-master automatically.

The maximal wiring lenght depends

on the used baud rate.

Connections:

The terminals (signals) VP and GND

are only to be used to connect the

external terminating resistors. There

Baud rate

Max. wiring

lenght

93,745 kbit/sec.  1200m
187,5   kbit/sec.  1000m
500   kbit/sec.  400m
1,5

Mbit/sec. 200m

3 – 12 Mbit/sec. 100m

Summary of Contents for Z7510







































































Search results

Summary of Contents for Z7510

Reviews:

Related manuals for Z7510

Brands by name

Popular brands

Strack Z7510, Operating Instruction

Search results

Summary of Contents for Z7510

Reviews:

Related manuals for Z7510

Brands by name

Popular brands