Spirent TestCenter Getting Started With Download | Manualshive

Page: 47 / 86

background image

Getting Started

Procedure 9: Confirm the Ethernet Link

Getting Started with Spirent TestCenter

|

47

Procedure 9: Confirm the Ethernet Link

If you have not already connected the chassis to a PC, hub, or LAN, do so now. See

Table 1-1 on page 30

for required cable connections.

Use standard network troubleshooting techniques to verify that the network can see the
chassis. Ping the Ethernet link between the PC and the chassis, and ping the chassis’ IP
address. If there are problems with the network connection, contact your network
administrator.

«
...
45
46
47
48
49
...
»

Summary of Contents for TestCenter























































































Reviews:

No comments

Related manuals for TestCenter

Univerge SV8100

Brand: NEC Pages: 44

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: Xinje Pages: 76

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

Brand: Furuno Pages: 24

Brand: SeaLevel Pages: 17

Brand: TRENDnet Pages: 2

Brand: Usr Pages: 2

Brand: Cypress Semiconductor Pages: 11

HBJC924R3288DG2NS Series

Brand: JETWAY Pages: 6

SmartNode 4520 Series

Brand: Patton electronics Pages: 90

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

RocketCache 3240X8

Brand: HighPoint Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands