5-48
3-6.
IR TRANSMITTER ADJUSTMENTS
Adjust using a IR receiver jig (J-6082-383-A).
Switch setting:
LASER LINK ................................................ ON (Red LED is lit)
1. IR Video Carrier Frequency Adjustment
(MA-330 board)
Mode
Camera standby
Subject
Arbitrary
Measurement Point
Pin
5
of CN003 of IR receiver jig
(RF) (Or Pin
!§
of IC8401)
Measuring Instrument
Frequency counter
Adjustment Page
D
Adjustment Address
90
Specified Value
f = 11.75 ± 0.05 MHz
Connection of Equipment
Connect the measuring device as shown in the following figure,
and adjust.
Fig. 5-3-12
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 2, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
3)
Select page: D, address: 90, change the data, and set the video
carrier frequency (f) to the specified value.
4)
Press the PAUSE button of the adjustment remote commander.
5)
Select page: 2, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
6)
Select page: 0, address: 01, and set data: 00.
Main unit
IR receiver jig
CN003
pin
5
Frequency counter
2. IR Video Deviation Adjustment (MA-330 board)
Mode
VTR playback
Signal
Alignment tape:
For audio operation check
(XH5-3 (NTSC))
(XH5-3P (PAL))
Measurement Point
VIDEO OUT terminal of IR receiver
jig (Terminated at 75
Ω
)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
91
Specified Value
A = 1.00 ± 0.05 V
Connection of Equipment:
Connect the measuring device as shown in the following figure,
and adjust.
Fig. 5-3-13
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 91, and change the data, set the video
signal amplitude (A) to the specified value.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
For NTSC model
For PAL model
Fig. 5-3-14
Main unit
IR receiver jig
VIDEO
OUT
75
Ω
75
Ω
(1-247-804-11)
Oscilloscope
White (100%)
A
H
White (100%)
A
H
Summary of Contents for Handycam Vision DCR-TRV5
